insulating ceramic paint and insulating paint additivesInsulating Roof Paint
Waterproofs, Insulates,
Reduces Sound
Selected by NASA as   "NASA Spinoff Technology Products for 2003"insulating paints and paint additives insulate,reduce energy costs,save money and improve comfort
insulating ceramic house paint

How to Apply Energy Saving
Insulating Roof Coatings

Hy-Tech Cool Roof Coatings are designed to insulate,seal, restore and protect roof surfaces. You don't have to tear off and dispose of your old roof, Hy-Tech Roof Coatings are up to 10 times lighter than traditional materials, so there's minimal weight or stress on your building, No fumes from tar and no hazardous materials to take to the landfill. Hy-Tech Insulating Roof Paints offer superior mildew resistance, soundproofing, UV reflectivity, and are resistant to ozone, acid rain and other air-borne contaminants. Energy savings are a big plus with Hy-Tech Roof Coatings...reduce heating and air conditioning costs.
MATERIAL LIST:
Cleaning products
"BOND IT" roof primer/sealer
Patching/Caulking materials
Hy-Tech Roof Coating
(Print out Material work Sheet) [worksheet.doc]

Download Application Instructions pdf file how to paint your roof

SURFACE PREPARATION: Power washing is recommended to insure a clean firm surface. To remove dirt, grease, milldew, fungus, etc., scrub with Hy-Tech House Wash  or a solution made with 16 fluid ounces (473 mL) of liquid household bleach and 2 fluid ounces (59 mL) of detergent in one gallon (3.785 L) of water. Rinse thoroughly with clean water and allow to dry. You should have a completely clean and firm surface before any new coating is applied. Avoid using cleaners with built-in wax or silicon additives since this may affect coating bond.
Patch or caulk all cracks, seams, flashing's and roof penetrations and make any necessary repairs or replacements to damaged or leaking roof materials. Caulk all cracks 1/8" or larger, use polyester tape and Bond It to repair flashing's and seams. Look out for these trouble spots:
Flashing's: All flashing's should fit tightly to the roof.
They should be held firmly by screws or taped down.
Damaged or rusty molding's and flashing's should be repaired, or removed and replaced.
Stacks and Vents: Stacks and vents remove excess moisture and fumes from your home.
Faulty or poor performing stacks or vents will allow moisture to accumulate between the ceiling and the roof and cause condensation. They should be repaired or replaced, or added, if necessary.
Seams, Cracks, and Stress Areas: The same repair procedure generally applies to seams, cracks, and stress areas. Remove all dried-out caulk or coating. On seams, tighten screws if necessary. Seams, cracks, and stress areas over 1/4" wide should be repaired using polyester woven reinforcement. Always put membrane over the entire seam - not just the portion that looks faulty.
Ponding Water: Any area of a roof where water may pond must be repaired by installing drains, polyurethane foam build-up, application of our Elasto Patch compound, or any means necessary to remove and prevent ponding water.


PRIMING:
NEW or PREVIOUSLY PAINTED SURFACES: Prime with Hy-Tech #1220 Bond-It before applying Hy-Tech Roof Coating. "Bond It" will penetrate and seal the surface so that you start with a clean, firm, base for the finish coating.

NEW METAL SURFACES: Galvanized and aluminum metal requires special primers, use one coat #15 Aqua Prime

RUSTY METAL: Prime with #18 White Latex Metal Primer or #15 Aqua Prime after using our new #17 Rust Reform rust conversion liquid.

APPLICATION: Once the roof is clean and primed apply the Finish/Top Roof Coating. Apply only at temperatures above 50 F. (10 C). Stir thoroughly before using and occasionally while using. May be applied to dry or slightly damp surfaces, using brush, roller or spray. Apply generously, working the Coating into pores and cracks. Try to apply the Coating as smoothly as possible. A minimum of two coats is recommended. Two thin coats are always preferable to one thick coat. Each coat should be applied perpendicular to the previous coat creating a checkerboard pattern. This guarantees no thin areas and a more uniform finish.
THINNING: Hy-Tech Roof Coatings are ready to use and should be applied full strength as they are received in the can. Any thinning of the Coating will reduce the percentage of solids, which will adversely affect the durability of the applied coating.
COVERAGE: On a rough porous surface, such as concrete tile, one gallon will usually cover from 75 to 100 sq.ft. On porous surfaces, the coverage on the second coat normally will be greater than the first coat. On smooth, non-porous surfaces, such as sheet metal, the coverage rate will be 100-150 sq.ft. per gallon.
DRYING TIME: Drying time will vary depending on surface and air temperature, humidity, wind or air movement, exposure to sunlight, etc. Under ideal drying conditions, Hy-Tech Roof Coatings form a dew and drizzle resistant film in approx. 4 - 6 hours after application. Allow the first coat to dry 8 - 12 hours before applying the second coat. Drying times will vary depending on temperature, humidity and location. Longer drying time is needed if the temperature is colder than 50 F., if too thick a coat is applied, if the relative humidity is higher than 90%, if the air is calm, or the surface is not exposed to direct sunlight.
CLEAN UP: Any drips, splatters, overspray or spills on shrubbery, walkway's, drive-ways, or sides of mobile homes must be cleaned up immediately before Coating dries. NOTE: If Coating is spilled or splashed remove it at once, using water from a hose, warm soapy water, or alcohol solvent. Coating not removed before it dries will be almost impossible to remove. Clean hands, brushes, rollers, tools and other equipment immediately after use in warm, soapy water.

WEATHER CONSIDERATION: Before application, KEEP FROM FREEZING. Apply only at temperatures above 50 F. Apply only when weather will be fair for a sufficiently long time for the Coating to dry. Do not apply late in the afternoon or early evening when a heavy dew could develop on the coating surface before it dries thoroughly. A very heavy rainstorm, such as those common in tropical climates, could wash the Coating off during the first few hours after application, if it has not dried thoroughly.
Spray painting makes short work of applying roof coatings, see our tutorial below on "How to Spray Paint", it's easier than you think.
How To Paint Menu:
How to Measure your roof
(Print out roof material work Sheet) [worksheet.doc]
Paint Metal Roofs
Wood Decks, Fences and Siding, Introduction
Cleaning Wood Decks, Fences and Siding
Refinishing Wood Decks, Fences and Siding
Reduce Attic Heat with Radiant Barrier Paint
Painting Ceilings with Insulating Paint
Painting Walls and Trim
Roof Coatings Application
Insulate RV and Mobile Home with Roof Paint
Paint Siding
Paint Stucco
Use a Roller with no mess
How to Spray Paint
General Painting Tips
Prices & Ordering Information |  International Buyers  |  Contact |  Questions?
Insulating Paint Additive |  Insulating Paints |  Sundries/Supplies |  HOME

Copyright 2002 - 2013 All Rights Reserved.
Affiliates: Home Improvement Center Insulating House Paints Hy-Tech Insulating Paint Sales Hy-Tech Insulating additives for paint Hy-Tech ceramic additives for paint Hy-Tech insulating ceramic additives that make paint insulate Insulating Paint